Electromagnetic Induction: Six Formulas, One Idea

Thomas Lee Abshier, ND ·18

One idea under six formulas

When the magnetic field threading a loop of wire changes, a voltage appears around that loop. That single statement is electromagnetic induction, and every formula a student memorizes for this chapter is that statement viewed from a different angle.

I recently saw a study card that lists six of them: magnetic flux, Faraday’s law, Lenz’s law, motional EMF, self-inductance, and the AC generator. Cards like that are useful for an exam, but they can leave the impression of six separate laws. I want to walk through them in order and show how each one grows out of the one before it.

The discovery itself belongs to Michael Faraday, who announced it in 1831. Joseph Henry found the same effect in America at about the same time. Within fifty years, their bench-top curiosity had become the dynamo, and within a hundred it was lighting the world.

Magnetic flux: what is being counted

Magnetic flux is how much magnetic field passes through a surface. Picture field lines as threads and the loop as a hoop; flux counts the threads passing through the hoop.

\Phi = \vec{B}\cdot\vec{A} = BA\cos\theta

Here B is the field strength in tesla, A is the area of the loop in square meters, and θ is the angle between the field and the line perpendicular to the loop’s face. The unit of flux is the weber (1 Wb = 1 T·m²).

The cosine matters. When the loop faces the field squarely, θ = 0 and the flux is the full BA. When the loop is turned edge-on, θ = 90° and no field lines pass through, so the flux is zero even in a strong field.

This gives three ways to change flux, and each will reappear below:

  1. Change the field strength B (move a magnet closer, or change the current in a nearby coil).
  2. Change the area A (slide a bar along rails to enlarge the circuit).
  3. Change the angle θ (rotate the loop, as in a generator).

Faraday’s law: the rate is what counts

The induced voltage, called the electromotive force or EMF, depends on how fast the flux changes, not on how much flux there is. A strong, steady magnet resting inside a coil produces nothing. A weak magnet moved quickly through the coil produces a pulse.

\varepsilon = -N\frac{d\Phi}{dt}

N is the number of turns in the coil. Each turn encloses roughly the same changing flux, and the turns are in series, so their voltages add. A coil of 500 turns gives 500 times the EMF of a single loop.

A quick example shows the scale. Suppose a 200-turn coil sees its flux rise from zero to 0.003 Wb in 0.05 seconds. The rate of change is 0.06 Wb/s, and the EMF is 200 × 0.06 = 12 volts. Halve the time, and the voltage doubles.

Faraday’s own experiment worked exactly this way. He wound two coils on an iron ring and connected a galvanometer to one of them. The needle stayed still while a steady current ran in the other coil. It jumped only at the moment he closed or opened the switch, when the current, and so the flux, was changing.

The EMF is a push on the charges around the loop. If the loop is closed, a current flows. If the loop is broken, the EMF still appears as a voltage across the gap.

Lenz’s law: the meaning of the minus sign

The study card gives Lenz’s law its own formula, but it is the same equation as Faraday’s. Lenz’s law is the minus sign. It says that the induced current always flows in the direction that opposes the change in flux that caused it.

\varepsilon = -\frac{d\Phi}{dt}

Push the north pole of a magnet toward a coil, and the coil’s current makes its near face a north pole too, pushing back. Pull the magnet away, and the current reverses, making the near face a south pole that pulls on the retreating magnet. Either way, the coil resists what you are doing.

The reason is conservation of energy. Suppose the sign were the other way, so the induced current helped the change along. A magnet nudged toward a coil would be pulled in faster, which would induce more current, which would pull harder. You would get unlimited energy from a small push. The minus sign forbids that. The electrical energy delivered by the coil is paid for by the work your hand does against the opposing force.

This is easy to feel. Drop a strong magnet down a copper pipe, and it drifts down slowly, because currents swirling in the copper (eddy currents) oppose its fall. The same principle brakes trains and roller coasters without any contact between the parts.

Motional EMF: changing the area

The second way to change flux is to change the area. Lay two parallel metal rails in a uniform magnetic field, connect them at one end, and slide a metal bar along them. The bar, the rails, and the connecting end form a rectangle that grows as the bar moves.

\varepsilon = BLv

L is the length of the bar between the rails and v is its speed. The derivation is one line. In a time dt, the bar moves a distance v·dt, so the area grows by L·v·dt and the flux grows by B·L·v·dt. Divide by dt, and the EMF is BLv.

A bar 0.5 m long moving at 4 m/s through a 0.2 T field produces 0.2 × 0.5 × 4 = 0.4 volts.

There is a second way to see the same result, and I find it the more satisfying one. The free electrons in the bar are moving with the bar through the field. A charge moving through a magnetic field feels a sideways force, the Lorentz force F = qvB. That force shoves the electrons toward one end of the bar, and the pile-up of charge is the voltage. Nothing about flux needs to be mentioned.

The two pictures agree, and that agreement is not an accident. In one frame of reference the cause looks like a magnetic force on moving charges; in another it looks like a changing field. Einstein opened his 1905 paper on special relativity with exactly this puzzle: a magnet moving past a conductor and a conductor moving past a magnet give the same current, yet the textbook explanations of the two cases were entirely different. Resolving that asymmetry was one of the threads that led him to relativity.

Lenz’s law shows up here as well. Once current flows in the bar, the field pushes back on that current with a force that opposes the motion. To keep the bar moving at constant speed, you have to keep pushing, and your work becomes the electrical energy in the circuit.

Self-inductance: a coil resisting itself

So far the changing flux has come from outside the coil. But a current in a coil makes its own magnetic field, and that field threads the coil’s own turns. If the current changes, the coil’s own flux changes, and Faraday’s law applies to the coil itself.

\varepsilon = -L\frac{dI}{dt}

L here is the inductance, measured in henries. It gathers up everything about the coil’s geometry (the number of turns, the area, the length, and whether there is an iron core) into one number that says how much flux the coil makes per ampere. The minus sign is Lenz’s law again: the self-induced EMF opposes the change in current.

The result is that an inductor behaves like electrical inertia. It does not resist current; it resists a change in current. Switch on a circuit with a large coil, and the current climbs gradually instead of jumping. Switch it off suddenly, and the coil fights to keep the current going, sometimes producing a spark across the switch. A 2-henry coil whose current drops 1 ampere in a millisecond produces 2 × 1 ÷ 0.001 = 2,000 volts.

Engineers put this to use everywhere. The ignition coil in a gasoline engine interrupts a current on purpose to get the high voltage that fires the spark plug. Inductors smooth the output of power supplies, and paired with capacitors they set the frequency of radio tuners.

The energy for that opposition is stored in the coil’s magnetic field, in the amount ½ LI². When the current falls, the field collapses and gives that energy back.

The AC generator: changing the angle

The third way to change flux is to change the angle, and that is how nearly all of the world’s electricity is made. Spin a coil of N turns and area A at a steady angular speed ω in a field B. The angle grows steadily, θ = ωt, so the flux through the coil is NBA cos ωt, rising and falling as the coil turns.

Apply Faraday’s law, and the derivative of a cosine is a sine:

\varepsilon = NBA\omega\sin(\omega t)

The output is a sine wave that reverses direction twice per turn. That is alternating current. The peak voltage is NBAω, so a generator designer can raise the output by adding turns, strengthening the magnets, enlarging the coil, or spinning it faster.

One detail surprises people. The EMF is greatest when the coil is edge-on to the field, at the moment the flux through it is zero. It is zero when the coil faces the field squarely and the flux is greatest. That is Faraday’s law in plain view: the voltage tracks the rate of change of flux, and the flux changes fastest as it passes through zero.

Lenz’s law is what makes a generator a machine for converting work into electricity. When no current is drawn, the shaft turns easily. Connect a load, and the induced current makes a magnetic force that resists the rotation. The turbine must then push harder, and the steam, water, or wind driving it supplies the energy that comes out of the wall socket. In North America, the shaft is held to a speed that makes the voltage reverse 60 times per second; in most of the rest of the world, 50.

In the summer of 1973 I interned at the Los Angeles Department of Water and Power while it was building the Castaic pumped-storage project. A pumped-storage plant shows the symmetry of induction well. When demand is high, water falls from an upper reservoir through the turbines and the machines run as generators. When demand is low, the same machines are driven as motors from the grid and pump water back uphill. Induction works in both directions.

Putting the six back together

Seen together, the six formulas are one law applied to different situations.

Formula What changes the flux Role
Φ = BA cos θ — Defines what is being counted
ε = −N dΦ/dt Anything The law itself (Faraday)
Minus sign Anything The direction: induced effects oppose the change (Lenz)
ε = BLv Area A grows Moving conductor
ε = −L dI/dt B from the coil’s own current Self-inductance
ε = NBAω sin ωt Angle θ rotates Generator

James Clerk Maxwell took the final step in the 1860s. He recognized that the changing magnetic field produces an electric field in space whether or not any wire is present; the wire merely lets us detect it by giving the charges a path. In his equations, Faraday’s law becomes a statement about the fields themselves. Paired with his own addition, that a changing electric field produces a magnetic field, it predicted waves of electric and magnetic fields regenerating each other as they travel at the speed of light. Light, radio, and every wireless signal are induction carried into empty space.

The formulas tell us precisely what happens and how much. They do not tell us what a field is, or why a change in one should call forth the other. Physics answered the “how” with remarkable completeness in the nineteenth century, and that answer is what lights our homes. The deeper question of what is actually happening in space when a field changes remains open, and I find it one of the most interesting questions in physics.